Home » Products » Heated Hose » Low temperature& low pressure » Constant Temperature Water Heating Hose Buyer FAQ for 100°C Process Water Lines

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Constant Temperature Water Heating Hose Buyer FAQ for 100°C Process Water Lines

JINGCHENG Water Heating Hose is an electrically heated constant-temperature hose for heated water and aqueous solution transfer lines, heat resistant up to 100°C, with higher temperatures on request. This buyer FAQ answers the questions process engineers ask most often, from the seven catalog bores between 1/4" and 1" ID and working pressures from 173 bar to 75 bar, to voltage, sensor and what to send for a quotation.
Availability:
Quantity:
  • Soren20061120

  • JINGCHENG

  • 3917290000 3904610000 3917390000

Constant Temperature Water Heating Hose Buyer FAQ for 100°C Process Water Lines

JINGCHENG Water Heating Hose is an electrically heated constant-temperature hose for heated water and aqueous solution transfer lines, heat resistant up to 100°C, with higher temperatures on request. This buyer FAQ answers the questions process engineers ask most often about the JINGCHENG Water Heating Hose, using the 100°C rating and the seven-size catalog table, from bore and pressure to voltage, sensor and what to send for a quotation.

About This Buyer FAQ

Buyers who specify a constant temperature water heating hose for the first time usually ask the same questions: what the hose is for, how hot it can run, which size to choose, which voltage and sensor to order, and what to send for a quotation. This FAQ answers those questions with the figures published in the JINGCHENG 2025 Electrically Heated Hose Catalog for the Water Heating Hose, listed under constant temperature hoses.

The catalog rates the hose at heat resistance up to 100°C, with higher temperatures available on request, and states that every line can be customized to your requirements. The seven-size standard table covers 1/4" to 1" inner diameter.

Q1. What is the hose used for?

It is an electrically heated hose for heated water and aqueous solution transfer lines that must hold a set temperature between two connection points. An unheated water line loses heat to the room, so the temperature at the outlet drifts and, in cold areas, the line can cool far below the process set point. The JINGCHENG hose heats and insulates at the same time. The heating layer is made of uniformly braided heating elements, which minimize temperature differences along the inner wall, and the hose is built with high-efficiency insulation selected with the surface temperature in mind.

Q2. How hot can the hose run?

The standard catalog rating is 100°C. If the process needs a higher temperature, say so in the enquiry; a higher rating is available on request and must be confirmed before the hose is built. Do not set the controller above the rating marked on the hose.

Q3. Which sizes are listed, and what pressure can they take?

Seven standard inner diameters from 1/4" to 1" are listed, with ID and OD tolerance of ±0.2 mm on the outer diameter column:

Inner Diameter (inch)

Outer Diameter (mm ±0.2)

Working Pressure (bar)

Working Pressure (psi)

Burst Pressure (bar)

Burst Pressure (psi)

Min. Bend Radius (mm)

1/4"

9

173

2501

690

10005

30

5/16"

11

158

2284

630

9137

40

3/8"

12.4

135

1958

540

7830

60

1/2"

15.9

118

1704

470

6815

150

5/8"

19

88

1269

350

5075

180

3/4"

22.6

85

1234

340

4930

260

1"

29.5

75

1088

300

4350

300

Data source: JINGCHENG 2025 Electrically Heated Hose Catalog. Heat resistance up to 100°C; higher temperature on request. Confirm the rating at your operating temperature with our engineers when ordering.

Working pressure falls as the bore grows, from 173 bar (2501 psi) at 1/4" to 75 bar (1088 psi) at 1". Burst pressure is four times working pressure on each row. The 5/16" burst pressure is 630 bar (9137 psi); the psi figure printed for this row in the catalog is a typographical error and is replaced here by 630 bar × 14.5 and is not an operating value. Always size the line so that the highest system pressure stays below the working pressure for that bore.

Q4. How should I choose the bore and the bend radius?

Start from the required flow and the space available for bends:

  • 1/4", 5/16" and 3/8" have minimum bend radii of 30 mm, 40 mm and 60 mm, so they can follow equipment frames closely. Their working pressures are the highest in the table.

  • From 1/2" upward the minimum bend radius jumps to 150 mm and reaches 300 mm at 1". These bores move more water with less pressure drop, but they need more room at every turn and at the hose reel or rack.

Check the outer diameter as well (9 mm to 29.5 mm) when you select clamps, guides and wall pass-throughs. If you are unsure, send the flow, the route length and a simple sketch and our engineers will suggest a size.

Q5. Which voltage, power and sensor can I order?

Every hose is built to the controller it will be wired to. Catalog options are:

  • Rated voltage: 380 Vac, 220 Vac, 110 Vac, 12 Vdc or other

  • Temperature sensor: Type J or Type K thermocouple, Ni120, PT100, PT1000 or other

  • Rated power: 110, 150, 170 or 200 W/m, or other

  • Length: 3 m, 4.5 m, 5 m, 6 m, 10 m or other

  • End fittings: US, British or metric thread at each end, or other

Match the sensor type to the input of the existing temperature controller. A mismatch is a common cause of unstable readings.

Q6. What environment can it work in?

The catalog operating environment used for these heated hoses is ambient -40°C to +55°C, relative humidity not above 85%, and atmospheric pressure 86 kPa to 106 kPa. The surrounding air should not contain gases that corrode metal or damage insulation. For unusual environments, ask us to confirm a custom construction.

Q7. What matters most during installation?

The catalog prohibits twisting the hose about its own axis and warns that a bend tighter than the table radius can damage the hose. Connect one end first, let the hose find its natural lay, hold the fitting with a second spanner while tightening, and support the hose so it does not hang from its fittings. Leave a short straight section at each end before the first bend. These points are covered in more detail in our installation and routing notes; they are the items buyers most often ask about before placing an order.

Q8. What should I send for a quotation?

  1. Medium (water or the aqueous solution) and the set temperature

  2. Maximum temperature (100°C standard; higher on request)

  3. Working pressure, including peaks

  4. Bore from the table above, or a custom size

  5. Length and any tight bends in the route

  6. Voltage, power, sensor type and pin layout

  7. Fitting standard and size at each end

With this information JINGCHENG can confirm the right constant temperature water heating hose and send a quotation quickly.

Previous: 
Next: 

Product Category

If you have any questions, please contact us via email or telephone and we will get back to you as soon as possible.

Contact Us

粤ICP备2023036405号-1

Copyright© 2023 JINCHEN ELECTRIC TRACING CO., LTD. All Rights Reserved.   Sitemap.   Support by Leadong