Home » Products » Heated Hose » High temperature& high pressure » Extruder Heated Melt Hose Ordering Specification Checklist for 250°C Extrusion and Line Marking Machines

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Extruder Heated Melt Hose Ordering Specification Checklist for 250°C Extrusion and Line Marking Machines

JINGCHENG Extruder Heated Hose is an electrically heated flexible melt connection for extrusion equipment, extruders and line marking machines, with a maximum service temperature of 250°C and a rating of 35 MPa at 250°C. This ordering checklist explains every item on the catalog order form, from the five standard bores of 3/8" to 1" ID to voltage, sensor, length, thread ends and pin layout.
Availability:
Quantity:
  • Soren20061116

  • JINGCHENG

  • 3917290000 3904610000 3917390000

Extruder Heated Melt Hose Ordering Specification Checklist for 250°C Extrusion and Line Marking Machines

JINGCHENG Extruder Heated Hose is an electrically heated flexible melt connection for extrusion equipment, extruders and line marking machines, with a maximum service temperature of 250°C and a rating of 35 MPa at 250°C. This page is a seven-item ordering checklist — process data, bore, length, electrical data, mechanical ends, model code and operating environment — so an extruder or line marking machine hose can be quoted and built right the first time.

Why an Ordering Checklist Matters for Extruder Heated Hose

An extruder heated hose is never a catalog part pulled from a shelf. Each hose is assembled to the electrical, mechanical and thermal data of one machine, so the quality of the inquiry largely decides how quickly a correct hose arrives. Incomplete requests are common: a bore without a length, a temperature without a sensor type, a thread size without the standard, or a connector described only as "same as the old one". This checklist lists every item the JINGCHENG catalog order form asks for, in the order an engineer will check it, so an extruder or line marking machine hose can be quoted and built right the first time.

JINGCHENG's extruder heated hose is an electrically heated flexible connection for common extrusion equipment, extruders and line marking machines. Its maximum service temperature is 250°C, and it is rated to withstand 35 MPa at 250°C. Heating elements are uniformly braided around the hose to minimize inner-wall temperature differences, and high-efficiency insulation is selected with the outer surface temperature in mind.

Checklist Item 1 — Process Data

  • Melt or material being conveyed, and whether it is an extrudate, a compound or a line marking material.

  • Set temperature and the maximum hose temperature required. The catalog service limit is 250°C; state the real operating value so the rating can be confirmed for your size.

  • Maximum pressure, including start-up peaks when the material is cold or the die is restricted.

  • Throughput, which drives the bore choice in the next item.

Checklist Item 2 — Bore From the Catalog Table

The extruder hose is listed in five standard inner diameters from 3/8" to 1". Choose the bore for throughput, then read the rest of the row:

  1. Working pressure is 110 bar (1595 psi) at 3/8", 88 bar (1269 psi) at 1/2", 70 bar (1015 psi) at 5/8", 65 bar (943 psi) at 3/4" and 57.5 bar (834 psi) at 1".

  2. Burst pressure is four times working pressure on each row, from 440 bar at 3/8" to 230 bar at 1".

  3. Minimum bend radius is 20, 25, 30, 60 and 85 mm from the smallest to the largest size.

  4. Outer diameter (mm ±0.2) is 15.5, 19, 22.7, 27 and 34 mm — the value to give if clamps, guides or a cable chain must be checked.

Inner Diameter (inch)

Outer Diameter (mm ±0.2)

Working Pressure (bar)

Working Pressure (psi)

Burst Pressure (bar)

Burst Pressure (psi)

Min. Bend Radius (mm)

3/8"

15.5

110

1595

440

6380

20

1/2"

19

88

1269

350

5075

25

5/8"

22.7

70

1015

280

4060

30

3/4"

27

65

943

260

3770

60

1"

34

57.5

834

230

3335

85

Data source: JINGCHENG 2025 Electrically Heated Hose Catalog. Maximum service temperature up to 250°C; 35 MPa at 250°C. Confirm the rating at your operating temperature with our engineers when ordering.

If your process needs a bore or pressure outside these five rows, say so in the inquiry; other sizes are made to order.

Checklist Item 3 — Length and Route

Catalog lengths are 3 m, 4.5 m, 5 m, 6 m, 10 m or other. Measure the route between connection points with the head or die in its working position, add allowance for movement, and check that the route never forces a bend tighter than the radius of the chosen row. Note any moving axis, vibration source or hot surface the hose will pass.

Checklist Item 4 — Electrical Data

  • Supply voltage: 380 Vac, 220 Vac, 110 Vac, 12 Vdc or other, and whether supply is single-phase or three-phase (for example 3X220, three-phase four-wire 220 V).

  • Rated power: 110, 150, 170 or 200 W/m, or another value matched to the heat demand of the melt.

  • Sensor: Type J or Type K thermocouple, Ni120, PT100 (two-wire or three-wire) or PT1000 — always the type the extruder zone controller reads.

  • Pin layout: the function of each pin at the host end and at the head end. A photo or drawing of the existing connector pin table removes most of the back-and-forth.

Checklist Item 5 — Mechanical Ends

State the thread standard at each end separately — US, British or metric — together with size and sealing type. The two ends of an extruder hose are often different, for example a melt pump outlet on one side and a die or applicator inlet on the other.

Checklist Item 6 — Inner Tube Type and Model Code

The catalog model code collects the core data in one line. JCH-200-16-B-3X220-P2-8 reads as 200°C working temperature, Φ16 mm bore, inner-tube type B, three-phase four-wire 220 V supply, PT100 two-wire sensor and 8 MPa working pressure. Inner-tube options are B (stainless steel corrugated tube), TB (PTFE hose with stainless steel braid), T (PTFE hose) and X (special material). Giving a draft code, even with question marks, shows the engineer at a glance what is fixed and what is open.

Checklist Item 7 — Operating Environment

The catalog operating conditions are ambient -40°C to +55°C, relative humidity not above 85%, atmospheric pressure 86–106 kPa and supply voltage 12–380 Vac. Mention corrosive gases, conductive dust or other unusual conditions near the extrusion line; special environments require a custom build.

How the Order Proceeds

  1. Inquiry with the checklist data above.

  2. Specification confirmation — JINGCHENG engineers propose the most suitable specification as a quotation reference.

  3. Quotation and purchase order.

  4. Production in our factory to the confirmed specification.

  5. Inspection and packing — every hose is checked for defects.

  6. Shipment to the address you designate.

Catalog Uses

Typical orders cover heated melt lines between melt pump, filter or screen changer and die; flexible heated transfer between extrusion modules; heated delivery of marking material from melter to applicator on line marking machines; and OEM hoses built to a machine builder's electrical and fitting standard.

Send your completed checklist, and JINGCHENG will return a matching extruder heated hose specification and quotation.

Previous: 
Next: 

Product Category

If you have any questions, please contact us via email or telephone and we will get back to you as soon as possible.

Contact Us

粤ICP备2023036405号-1

Copyright© 2023 JINCHEN ELECTRIC TRACING CO., LTD. All Rights Reserved.   Sitemap.   Support by Leadong