| Availability: | |
|---|---|
| Quantity: | |
Soren20061117
JINGCHENG
3917290000 3904610000 3917390000
JINGCHENG Paraffin Wax Hose is an electrically heated wax delivery hose for 3D printing equipment, heat resistant up to 230°C and upgraded generation by generation together with customers' printer models. This page sets out a step-by-step start-up and shutdown routine for wax feed lines, plus set-up checks and quick fixes for slow starts, because most wax-line problems happen while the wax is melting or solidifying.
Paraffin and other waxes are solid at room temperature and fluid only while they are held above their melting range. On a wax-based 3D printer, that means the feed line between the melt tank and the print head goes through a solid-to-liquid transition every time the machine is started and a liquid-to-solid transition every time it is stopped. Most wax-line problems — slow starts, partial blockages, uneven flow in the first minutes of a job — happen during these two transitions rather than during steady printing. A clear start-up and shutdown routine, built around a properly heated hose, prevents them.
JINGCHENG's paraffin wax hose, also called the 3D printer wax delivery hose, is commonly used in 3D printing equipment. 3D printing is a young industry, and JINGCHENG's wax hose has been upgraded generation by generation along with customers' machine models and technology; it matches 3D printers very closely and its quality is now very stable.
The hose both heats and insulates. Its heating layer is made of uniformly braided heating elements that minimize the temperature difference along the inner wall, so the whole bore warms at the same rate instead of leaving cold sections where wax can stay solid. High insulation-efficiency materials, chosen with the surface temperature in mind, hold that heat in the line. The hose is heat resistant up to 230°C, with higher temperatures available on request.
Confirm the wiring. The hose must be connected according to its technical data and the pin table supplied with it, including the sensor wires.
Match the sensor to the controller. The catalog offers Type J or Type K thermocouples, Ni120, PT100 and PT1000; the controller must be configured for the sensor actually fitted.
Check the route. The hose must not be twisted sideways and must not be bent tighter than the minimum bend radius of its size, especially next to the fittings.
Check the environment. The catalog operating window is ambient -40°C to +55°C with relative humidity not above 85%, free of corrosive gases, conductive media and severe mold.
The paraffin wax hose uses the standard seven-row table:
Inner Diameter (inch) | Outer Diameter (mm ±0.2) | Working Pressure (bar) | Working Pressure (psi) | Burst Pressure (bar) | Burst Pressure (psi) | Min. Bend Radius (mm) |
|---|---|---|---|---|---|---|
1/4" | 9 | 173 | 2501 | 690 | 10005 | 30 |
5/16" | 11 | 158 | 2284 | 630 | 9137 | 40 |
3/8" | 12.4 | 135 | 1958 | 540 | 7830 | 60 |
1/2" | 15.9 | 118 | 1704 | 470 | 6815 | 150 |
5/8" | 19 | 88 | 1269 | 350 | 5075 | 180 |
3/4" | 22.6 | 85 | 1234 | 340 | 4930 | 260 |
1" | 29.5 | 75 | 1088 | 300 | 4350 | 300 |
Data source: JINGCHENG 2025 Electrically Heated Hose Catalog. Heat resistance up to 230°C; higher temperature on request. Confirm the rating at your operating temperature with our engineers when ordering.
Small bores such as 1/4" and 5/16" (30 mm and 40 mm bend radius) suit compact print-head connections; larger bores give more flow on bulk wax supply lines but need a wider route.
Heat the tank and the hose together. Switch on hose heating at the same time as, or before, the melt tank, so that molten wax never enters a cold line.
Bring the hose to set point before pumping. Wait until the hose sensor reads the set temperature and has stabilized. Pumping into a hose that is still warming is the most common cause of a partial blockage at start-up.
Allow a short soak time. Any wax left in the bore from the last shutdown needs time to melt completely, not just at the sensor position. The even braided heating layer shortens this time, but it should still be part of the routine.
Start flow at low output. Prime the line slowly and watch for steady flow at the print head before switching to full production output.
Record the warm-up time. A start-up that suddenly takes longer than usual is an early sign of a wiring, sensor or controller problem.
Keep the hose set point within the wax supplier's recommended processing range and well inside the 230°C rating.
Do not let the hose be pulled into tight bends by moving axes or cable chains.
Watch for changes in pump pressure or flow; a rising pump load can mean a cooler section in the line.
Stop the pump first, then the heating. Stopping heat while the pump still runs pushes wax into a cooling line.
Decide whether to drain or to hold. For short breaks, keeping the hose at temperature is often simpler than a full cool-down and restart. For longer stops, follow the printer builder's procedure for draining or relieving the line.
Relieve pressure before any disconnection. Never open fittings on a heated or pressurized line.
Leave the hose in its normal route. Do not coil a cooling hose tighter than its bend radius; solidified wax makes the hose stiffer.
Hose heats slowly: check supply voltage and rated power against the order (110, 150, 170 or 200 W/m, or other).
Temperature reading looks wrong: confirm the controller is set for the fitted sensor type.
Flow is uneven only in the first minutes: extend the soak time before pumping.
Repeated problems at one spot: check that section for a tight bend or external damage, and contact JINGCHENG engineers.
Every hose is made to order: supply voltage 380 Vac, 220 Vac, 110 Vac, 12 Vdc or other; length 3 m, 4.5 m, 5 m, 6 m, 10 m or other; US, British or metric threads at each end; and a custom pin layout. A model code such as JCH-200-16-B-3X220-P2-8 records working temperature, bore, inner tube type, voltage, sensor and working pressure, so a proven specification can be repeated for each printer model. Operators should be authorized and trained; unauthorized modification voids the warranty.
Send the printer model, wax type and processing temperature, bore and length, supply voltage, sensor type, thread standard and pin layout. JINGCHENG engineers will confirm a paraffin wax hose specification and quotation; every hose is checked for defects before packing and shipment.
