| Availability: | |
|---|---|
| Quantity: | |
Soren20061120
JINGCHENG
3917290000 3904610000 3917390000
JINGCHENG Food Hose is an electrically heated hose for all kinds of food conveying equipment, built with a customized food-grade conveying inner tube and heat resistant up to 100°C, with higher temperatures on request. This page is a size and ordering checklist based on the figures in the JINGCHENG 2025 Electrically Heated Hose Catalog, so a food conveying line can be quoted and built to the right bore, length and electrical data the first time.
A food conveying heated hose is built to one line, not pulled from a shelf as a standard assembly. If the bore, length, set temperature or sensor type is missing from the enquiry, the hose that arrives may heat correctly but not fit the pump, the route or the controller. This page is a size and ordering checklist for the JINGCHENG Food Hose, based on the figures in the 2025 Electrically Heated Hose Catalog, so a 100°C food product line can be specified in one pass.
The catalog describes the Food Hose as suitable for all kinds of food conveying equipment, built with a customized food-grade conveying inner tube selected for the product, and states that every line can be customized to your requirements. Heat resistance is up to 100°C, with higher temperatures available on request.
Food product being conveyed, and whether it thickens as it cools.
Set temperature and the maximum hose temperature required. The standard catalog rating is 100°C; do not assume a higher rating unless it has been confirmed in the order.
Working pressure, including start-up peaks when the product is cold or a valve is closed.
Duty: continuous transfer, intermittent filling or a line that is cleaned and restarted every shift.
The inner tube is selected for the food product. Name the product and any cleaning medium in the enquiry so the tube can be matched correctly.
The Food Hose uses the catalog's seven-size standard table, from 1/4" to 1" inner diameter. Choose the bore for the required flow, then read the rest of that row before you freeze the route.
Inner Diameter (inch) | Outer Diameter (mm ±0.2) | Working Pressure (bar) | Working Pressure (psi) | Burst Pressure (bar) | Burst Pressure (psi) | Min. Bend Radius (mm) |
|---|---|---|---|---|---|---|
1/4" | 9 | 173 | 2501 | 690 | 10005 | 30 |
5/16" | 11 | 158 | 2284 | 630 | 9137 | 40 |
3/8" | 12.4 | 135 | 1958 | 540 | 7830 | 60 |
1/2" | 15.9 | 118 | 1704 | 470 | 6815 | 150 |
5/8" | 19 | 88 | 1269 | 350 | 5075 | 180 |
3/4" | 22.6 | 85 | 1234 | 340 | 4930 | 260 |
1" | 29.5 | 75 | 1088 | 300 | 4350 | 300 |
Data source: JINGCHENG 2025 Electrically Heated Hose Catalog. Heat resistance up to 100°C; higher temperature on request. Confirm the rating at your operating temperature with our engineers when ordering.
Read the row as a set, not as a single diameter:
Working pressure falls as the bore grows, from 173 bar (2501 psi) at 1/4" to 75 bar (1088 psi) at 1". The line pressure, including peaks, must stay below the working value for the chosen size.
Burst pressure is four times working pressure on each row. The 5/16" burst pressure is 630 bar (9137 psi); the psi figure printed for this row in the catalog is a typographical error and is replaced here by 630 bar × 14.5. Burst pressure is a safety margin, not an operating limit.
Minimum bend radius is 30 mm at 1/4", 40 mm at 5/16", 60 mm at 3/8", then rises to 150 mm at 1/2", 180 mm at 5/8", 260 mm at 3/4" and 300 mm at 1". From 1/2" upward the hose needs much more room at each turn.
Outer diameter (mm ±0.2) is the value to check against clamps, guides, tanks and cable chains: 9, 11, 12.4, 15.9, 19, 22.6 and 29.5 mm.
If the process needs a bore or pressure outside these seven rows, say so in the enquiry; other sizes are made to order.
Catalog length options are 3 m, 4.5 m, 5 m, 6 m, 10 m or other. Measure the route between the two connection points with the machine in its working position, add allowance for movement and for a short straight section at each fitting, and confirm that no bend is tighter than the radius of the chosen row. Note any moving axis, wash-down area or hot surface the hose will pass.
Every JINGCHENG food heated hose is built to the controller it will be wired to. State:
Supply voltage: 380 Vac, 220 Vac, 110 Vac, 12 Vdc or other.
Rated power: 110, 150, 170 or 200 W/m, or another value matched to the heat demand of the product and the length.
Sensor: Type J or Type K thermocouple, Ni120, PT100 or PT1000 — always the type the existing controller can read.
Pin layout at the machine end and at the outlet end. A photo or drawing of the connector pin table removes most of the back-and-forth.
The heating layer is made of uniformly braided heating elements, which minimizes temperature differences along the inner wall. The high-efficiency insulation is selected with the surface temperature in mind.
State the thread standard at each end separately — US, British or metric — together with size and sealing type. The two ends of a food conveying hose are often different, for example a pump outlet on one side and a filler or dosing inlet on the other.
Food product and cleaning medium
Set temperature and maximum temperature (100°C standard; higher on request)
Working pressure, including peaks
Bore from the table above, or a custom size
Length and a simple route sketch if the path is tight
Voltage, power, sensor type and pin layout
Fitting standard and size at each end
With this list JINGCHENG can confirm the size, build the hose to your parameters and send a quotation without a second round of questions.
