Views: 0 Author: JC Publish Time: 2026-11-16 Origin: JC
A PTFE hose is often specified because the liner is chemically inert and the catalog temperature window is wide. Those two facts are real, and they are why JINGCHENG PTFE cold hoses are used on strong-acid, alkali, solvent and high-purity chemical lines. They are not a reason to treat every published working-pressure figure as available at every temperature, or to assume that PTFE is compatible with everything.
Concentration, temperature and pressure act together. Fittings and metal reinforcement see the same duty, and not every catalog series shares the same upper temperature limit. This article is a practical checklist for reading chemical compatibility and working-pressure ratings together, using the figures in the JINGCHENG PTFE hose catalog. It does not replace a review of your exact medium, and it is not a chemical-resistance chart for substances the catalog does not list.
JINGCHENG smooth-bore PTFE tube (series JCC-00000-PTFE) is extruded, dried, high-temperature sintered and shaped from PTFE resin. The catalog states that it is suitable for strong acids and alkalis, strong oxidizing agents, reducing agents and various organic solvents, and that it is very suitable for transporting high-purity chemicals. The catalog temperature range for this series is −70 °C to +260 °C. The same media family appears across the PTFE inner-tube and braided-hose range, including steam, hot air and hot oil duties.
Two limits are easy to miss when the datasheet is read in a hurry:
Not every series is rated to +260 °C. Several smooth-bore and braided series are catalogued at −70 °C to +260 °C, but the braided convoluted series JCC-11100 is catalogued at −70 °C to +200 °C and the spiral-wound braided series JCC-03100 at −65 °C to +220 °C. A cleaning cycle, steam flush or hot-oil duty that is acceptable on a JCC-01100 hose may be outside the window of a JCC-11100 or JCC-03100 hose of the same nominal size. The table in section 4 lists the catalog temperature range for each series.
The catalog describes families of media, not a substitute for the exact chemical, concentration, temperature and exposure time on your line. If the medium is a mixture, a changing formulation, or a duty the catalog does not name, send the full composition to JINCHEN ELECTRIC TRACING CO., LTD. for confirmation before you order.
PTFE is widely recognised as resistant to a very broad range of industrial chemicals because of its fluorinated molecular structure. The well-established exceptions are a short list, principally molten alkali metals and elemental fluorine or certain strong fluorinating agents, especially at elevated temperature. Do not treat that short list as a licence to skip a review of concentration and temperature on an otherwise "compatible" acid or solvent. Compatibility is a function of the complete duty, not of the polymer name alone.
A finished PTFE hose is a system. The fluid-contact surface is PTFE, but the pressure-carrying and sealing parts often are not.
End fittings. The catalog assembly guides are clear that the working pressure of an assembly is limited by the weaker of the hose and the fittings, and that fittings must be matched to the diameters of the size you are using. The fitting material must also be compatible with the medium. A PTFE liner that is inert to a chloride-containing or acidic stream does not protect a fitting alloy that is not.
Metal reinforcement. Single and double 304 stainless steel braids, 304 spiral springs, wire-bundle braids and copper-plated steel wire spiral windings raise working pressure from the bare-tube range into tens of megapascals. Those metals sit outside the liner. If a small-molecule medium permeates the PTFE wall — a known behaviour of PTFE with some gases and certain solvents — or if the braid is wetted from the outside by a corrosive atmosphere, condensate or a spill, the reinforcement can be attacked even while the bore still looks intact.
Batch changeover. The non-stick bore is one reason PTFE is chosen for high-purity and multi-product lines, but the catalog still calls for the line to be flushed between incompatible media. Residue left in corrugations, in a fitting cavity or in a dead leg is a compatibility problem, not only a cleanliness problem.
If the line carries a low-conductivity flammable liquid, solvent or coating material at speed, chemical compatibility is necessary but not sufficient. Standard PTFE is an electrical insulator; JINGCHENG also supplies anti-static and conductive PTFE hose constructions for those duties, which is a separate decision from the pressure and temperature review in this article.
Published working-pressure figures in the JINGCHENG PTFE hose catalog are size- and construction-specific. They are the figures you should design against, not operating limits at every point in the temperature range.
As temperature rises toward the upper catalog limit, the mechanical strength of PTFE declines. The catalog therefore requires working pressure to be evaluated together with the actual operating temperature, the tube diameter, wall thickness, length, fitting design, pressure cycles and installation method. In practice this means:
Do not assume that the published working pressure for a size is available at +200 °C or +260 °C. Confirm the allowable pressure for your duty with the manufacturer. A line that is comfortably below the catalog rating at ambient conditions may not be once the process is hot.
Burst pressure is a safety margin, not an operating limit. On JCC-00000 the catalog burst figures run from 5.6 MPa down to 1.2 MPa depending on size; on JCC-01100, burst is roughly three times working pressure. Neither ratio is a licence to operate above the working-pressure figure.
Diameter matters as much as construction. On JCC-00000, catalog working pressure is 1.73 MPa (251.33 psi) at 1/4", 0.93 MPa at 1/2", 0.70 MPa at 1" and 0.40 MPa at 2". On JCC-01100, the same step-down appears at much higher pressures: 42 MPa at 1/4", 23 MPa at 1/2" and 10 MPa at 1". Choosing a larger bore to reduce pressure drop also reduces the catalog working pressure.
Reinforcement is what moves a line out of the low-pressure bare-tube range. A 1/4" bare smooth-bore tube is catalogued at 1.73 MPa; the 1/4" single-braid smooth-bore hose JCC-01106-PTFE is catalogued at 42 MPa. If the process is hot and pressurized, do not try to "make do" with an unreinforced tube because the medium is compatible with PTFE.
These figures must still be confirmed for the temperature, medium and pressure peaks of the actual line.
The table below restates catalog temperature ranges and selected working-pressure figures so they can be read together. It is a first-pass reference, not a derating curve. JINCHEN ELECTRIC TRACING CO., LTD. will confirm the allowable working pressure at your operating temperature when you send the duty.
Catalog series | Construction | Catalog temperature range | Selected catalog working pressure |
|---|---|---|---|
JCC-00000-PTFE | Bare smooth-bore PTFE tube | −70 °C to +260 °C | 1.73 MPa at 1/4"; 0.93 MPa at 1/2"; 0.40 MPa at 2" |
JCC-10000-PTFE | Bare convoluted PTFE hose | −70 °C to +260 °C | 0.4 MPa at 1/4" and at 1/2" |
JCC-20000-PTFE | Smooth-ID, corrugated-OD hose with 304 spiral spring | −65 °C to +260 °C | 2.64 MPa at 1/4"; 1.8 MPa at 1/2" |
JCC-01100-PTFE | Smooth-bore tube with a single 304 stainless steel braid | −70 °C to +260 °C | 42 MPa at 1/4"; 23 MPa at 1/2"; 10 MPa at 1" |
JCC-11100-PTFE | Convoluted hose with a 304 stainless steel braid | −70 °C to +200 °C | Up to 13.8 MPa at 1/4"; upper limit is +200 °C, not +260 °C |
JCC-01200-PTFE | Smooth-bore tube with a double 304 stainless steel braid | −70 °C to +260 °C | Up to 40 MPa, size-dependent |
JCC-03100-PTFE | Spiral-wound tube with copper-plated steel wire and 304 braid | −65 °C to +220 °C | Up to 44 MPa at 1/2"; upper limit is +220 °C |
Data source: JINGCHENG PTFE Hose Catalog. Figures are the published catalog values for the sizes shown. Confirm the allowable working pressure at the actual operating temperature; do not treat burst pressure as an operating limit.
Use the table in this order. First confirm that the maximum process temperature, including cleaning or sterilizing cycles, sits inside the temperature range of that series. Then compare your maximum system pressure, including peaks and pulsation, with the catalog working pressure for the bore you need, and treat that figure as one that must be confirmed at temperature. If the process is near the upper temperature limit, or the pressure is close to the published rating, say so on the inquiry. A change of construction — from JCC-00000 to JCC-20000 or JCC-01100, or from single braid to JCC-01200 or JCC-03100 — is often the correct answer.
The most demanding lines combine chemical attack, heat and pressure, rather than presenting only one of those conditions.
A strong acid or solvent that is acceptable in a PTFE tube at ambient temperature may be a different duty at elevated temperature, for the liner as well as the fittings and braid. Always state concentration and the maximum temperature together.
Steam, hot air and hot oil are why the catalog offers JCC-20000 (smooth-ID, corrugated-OD, 304 spiral spring, −65 °C to +260 °C, 2.64 MPa at 1/4") as well as braided constructions.
Pressure pulsation, frequent thermal cycling and vacuum each add mechanical load. JCC-21100 is catalogued as vacuum-resistant with a smooth bore for hygienic transfer up to +260 °C; if your line sees vacuum or clean-in-place heat-up, state that on the inquiry.
Installation mistakes can look like a material failure. Lateral twist, a bend tighter than the catalog minimum, or a fitting closed onto the wrong diameter can leak or burst a hose whose liner was chemically suitable. Those rules still belong on the pre-start checklist.
Work through this list before you request a quotation or a replacement hose:
Exact medium, including concentration and, for a mixture, the full composition.
Working temperature and the maximum temperature, including cleaning, sterilizing or short-term excursions.
Working pressure, pressure peaks or pulsation, and whether the line sees vacuum.
Required inner diameter, length and minimum bend radius of the routing.
The construction you are considering, or the series and part number of the hose being replaced (for example JCC-00000, JCC-01100 or JCC-01200).
End-fitting type and material, and whether the fittings must be chemically resistant to the same medium as the liner.
Duty: continuous transfer, intermittent, outdoor, or a special atmosphere around the hose.
For flammable or low-conductivity fluids, whether an anti-static or conductive construction is required.
Need help matching a PTFE hose to a chemical duty and a pressure at temperature? Send JINCHEN ELECTRIC TRACING CO., LTD. the medium and concentration, the working and maximum temperatures, the working pressure and peaks, the size and the fitting details. Our engineers will help you select a catalog series whose temperature window and construction match the line, and every JINGCHENG hose is inspected before packing and shipment.
PTFE Hose Chemical Compatibility and Temperature-Pressure Derating: A Practical Selection Checklist
On the Paint Line, Every Degree Counts: Heated Hoses in Automotive Coating
Why Does A PTFE Heated Hose Experience Uneven Temperature? Causes And Solutions
Troubleshooting Electrically Heated Hose Temperature Faults: Sensor, Controller and Wiring Checks
