| Availability: | |
|---|---|
| Quantity: | |
Soren20061117
JINGCHENG
3917290000 3904610000 3917390000
JINGCHENG Polyurethane Hose is an electrically heated hose for laminating machines and single- and two-component polyurethane compounding and connection equipment, heat resistant up to 180°C with higher temperatures on request. This page sets laminators, single-component systems, two-component systems and connection lines side by side, showing what the hose must do in each and which specification items matter most.
Polyurethane equipment comes in many forms — laminating machines, single-component systems, two-component systems and the connection lines that link one unit to another. The heated hose is the same product family in each case, but the points that matter when specifying it are not. This application matrix sets the main polyurethane uses side by side and shows, for each one, what the hose has to do and which specification items deserve the most attention.
JINGCHENG's dedicated polyurethane equipment hose is widely used on all types of laminating machines and on single- and two-component polyurethane compounding and connection equipment. Over many years its stable quality and complete customer service have built a large base of quality customers.
Heat resistance up to 180°C; higher temperatures can be built on request.
The hose heats and insulates: the heating layer is made of uniformly braided heating elements that minimize the temperature difference along the inner wall.
High insulation-efficiency materials are used with the hose surface temperature in mind.
Every hose is built to order for the application and for the temperature, viscosity and flowability of the material.
Application | What the hose must do | Specification focus |
|---|---|---|
Laminating machines | Keep PU adhesive at a steady temperature from supply unit to coating station | Small bore to limit material held in the line; sensor matched to the laminator controller; route within bend radius on the machine frame |
Single-component PU equipment | Hold one material at processing temperature between tank and applicator | Bore sized to output and line length; rated power suited to set point and ambient conditions |
Two-component PU equipment | Keep each component at its own set point until the mixing point | One heated line per component, each with its own sensor and controller channel; clear marking of both lines |
Connection lines between units | Carry warm material between separate machines without cooling | Length, thread standard at each end and pin layout defined for both connected units |
The polyurethane hose uses the standard seven-row table:
Inner Diameter (inch) | Outer Diameter (mm ±0.2) | Working Pressure (bar) | Working Pressure (psi) | Burst Pressure (bar) | Burst Pressure (psi) | Min. Bend Radius (mm) |
|---|---|---|---|---|---|---|
1/4" | 9 | 173 | 2501 | 690 | 10005 | 30 |
5/16" | 11 | 158 | 2284 | 630 | 9137 | 40 |
3/8" | 12.4 | 135 | 1958 | 540 | 7830 | 60 |
1/2" | 15.9 | 118 | 1704 | 470 | 6815 | 150 |
5/8" | 19 | 88 | 1269 | 350 | 5075 | 180 |
3/4" | 22.6 | 85 | 1234 | 340 | 4930 | 260 |
1" | 29.5 | 75 | 1088 | 300 | 4350 | 300 |
Data source: JINGCHENG 2025 Electrically Heated Hose Catalog. Heat resistance up to 180°C; higher temperature on request. Confirm the rating at your operating temperature with our engineers when ordering.
Note that the temperature rating for this product is 180°C, lower than the 230°C rating of several other JINGCHENG low-pressure hoses. Choose the set point of each line inside that limit, or ask for a custom higher-temperature build.
Laminator lines are often short and routed on a compact frame. The small bores (1/4" with a 30 mm bend radius, 5/16" with 40 mm, 3/8" with 60 mm) are easy to route and keep the adhesive volume in the line low. The sensor must suit the controller already on the machine.
Here the hose is sized mainly by output and length: a long line or high output usually calls for a larger bore, which reduces flow resistance. Larger bores need more space — 1/2" needs a 150 mm bend radius and 1" needs 300 mm.
Each component usually has its own viscosity and processing temperature, so each should run in its own heated line with its own sensor. Specifying the two lines together, with matching lengths and clearly defined pin tables, makes installation and later replacement simpler.
When the hose links two separate units, the details at both ends matter most: thread standard (US, British or metric), pin number, wire color and function at each end, and a length that avoids tight bends or strain.
Item | Catalog options |
|---|---|
Rated voltage | 380 Vac, 220 Vac, 110 Vac, 12 Vdc or other |
Temperature sensor | Type J or Type K thermocouple, Ni120, PT100, PT1000 or other |
Length | 3 m, 4.5 m, 5 m, 6 m, 10 m or other |
Rated power | 110, 150, 170 or 200 W/m, or other |
End fittings | US, British or metric thread at each end, or other |
A model code such as JCH-200-16-B-3X220-P2-8 records working temperature, inner diameter, inner tube type, supply voltage, sensor and working pressure, so each row of your own equipment list can be tied to one repeatable code.
Do not twist the hose sideways; lateral twisting can cause leakage, flow loss, hose damage or fire.
Avoid sharp bends, especially next to the fittings.
Wire each hose according to its technical data and pin table.
Operate within ambient -40°C to +55°C, relative humidity not above 85%, away from corrosive gases, conductive media and severe mold.
Only authorized, trained operators should handle the hose; unauthorized modification voids the warranty.
Send a list of your polyurethane machines with the material, processing temperature, bore, length, supply voltage, sensor and thread standard for each line. JINGCHENG engineers will turn it into a matching set of polyurethane hose specifications and a quotation; every hose is checked for defects before packing and shipment.
