Home » Products » PTFE Hose » Smooth Bore PTFE Tube Installation and Routing Guide for Chemical and Process Fluid Lines

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Smooth Bore PTFE Tube Installation and Routing Guide for Chemical and Process Fluid Lines

JINGCHENG Smooth Bore PTFE Tube (series JCC-00000-PTFE) is extruded, dried, high-temperature sintered and shaped from PTFE resin for strong acids, alkalis, oxidizers, reducing agents, organic solvents and high-purity chemicals from -70°C to +260°C. This installation and routing guide explains how to cut, connect and support the eleven catalog sizes from 5/32" (4.5 mm ID) to 2" (51 mm ID), keeping every bend within the 60 mm to 1200 mm minimum radius and the working pressure between 1.73 MPa and 0.40 MPa.
Availability:
Quantity:
  • Soren20061120

  • JINGCHENG

  • 3917290000 3904610000 3917390000

Smooth Bore PTFE Tube Installation and Routing Guide for Chemical and Process Fluid Lines

JINGCHENG Smooth Bore PTFE Tube (series JCC-00000-PTFE) is extruded, dried, high-temperature sintered and shaped from PTFE resin for strong acids, alkalis, oxidizers, reducing agents, organic solvents and high-purity chemicals from -70°C to +260°C. This installation and routing guide explains how to cut, connect and support the JCC-00000-PTFE smooth bore tube, keeping every bend within the catalog minimum radius and the pressure below the working value for the chosen size.

Why Installation and Routing Decide How a Smooth Bore Tube Performs

A smooth bore PTFE tube is straightforward to specify and easy to damage if it is cut poorly, bent too tightly or left unsupported. The JCC-00000-PTFE tube is a bare, unreinforced tube: it has a smooth, non-stick bore and no braid or spring to protect it against kinking. That is why the catalog minimum bend radii are large, and why the route has to be planned before the first cut. This guide walks through installation and routing of the JINGCHENG JCC-00000-PTFE standard smooth bore tube, using the figures in the PTFE Hose Catalog.

The tube is a special tube made from PTFE resin, produced by extrusion, drying, high-temperature sintering and shaping. The catalog temperature range is -70°C to +260°C. It is suitable for strong acids and alkalis, strong oxidizing agents, reducing agents and various organic solvents, and it is very suitable for transporting high-purity chemicals. Standard walls are 1.0 mm to 2.0 mm depending on size. Eleven standard sizes run from 5/32" (4.5 mm ID) to 2" (51 mm ID).

Step 1: Confirm the Size Against the Catalog Table

Before cutting, check that the chosen size covers the system pressure and the space available for bends.

Part No.

Nominal Size

Inner Diameter (mm ±0.2)

Outer Diameter (mm ±0.2)

Working Pressure (psi)

Working Pressure (MPa)

Burst Pressure (psi)

Burst Pressure (MPa)

Min. Bend Radius (inch)

Min. Bend Radius (mm)

Wall Thickness (mm)

JCC-00004-PTFE

5/32"

4.5

6.5

203.00

1.40

812

5.6

2.36

60

1.0

JCC-00006-PTFE

1/4"

6.8

8.8

251.33

1.73

754

5.2

5.12

130

1.0

JCC-00008-PTFE

5/16"

8.2

10.5

203.00

1.40

609

4.2

6.3

160

1.2

JCC-000010-PTFE

3/8"

10.3

12.7

169.17

1.17

507.5

3.5

8.66

220

1.2

JCC-000013-PTFE

1/2"

13.3

15.7

135.33

0.93

406

2.8

10.63

270

1.2

JCC-000016-PTFE

5/8"

15.9

18.3

106.33

0.73

319

2.2

15.75

400

1.2

JCC-000019-PTFE

3/4"

19.8

22.3

116.00

0.80

348

2.4

19.69

500

1.5

JCC-000025-PTFE

1"

25.7

29.7

101.50

0.70

304.5

2.1

23.62

600

2.0

JCC-000032-PTFE

1-1/4"

31.7

35.7

91.83

0.63

275.5

1.9

31.50

800

2.0

JCC-000038-PTFE

1-1/2"

38.5

42.5

72.50

0.50

217.5

1.5

35.43

900

2.0

JCC-000050-PTFE

2"

51

55

58.00

0.40

174

1.2

47.24

1200

2.0

Data source: JINGCHENG PTFE Hose Catalog (JCC-00000-PTFE Series). Operating temperature range: -70°C to +260°C. All specifications can be customized according to customer parameters.

Select a size whose working pressure is above the highest pressure the line will see. The highest rating in the range is 1.73 MPa (251.33 psi) at 1/4"; it then falls with diameter to 0.40 MPa at 2". Two points that affect routing as well as pressure:

  • 5/32" is not the strongest size. At 1.40 MPa it is rated below the 1/4" tube, because both have a 1.0 mm wall.

  • 3/4" is rated slightly above 5/8" (0.80 MPa against 0.73 MPa) because its wall is 1.5 mm rather than 1.2 mm.

Burst pressure (from 5.6 MPa down to 1.2 MPa) is a safety margin, not an operating limit. ID and OD tolerance is ±0.2 mm; use the actual outer diameter when you select fittings and clamps.

Step 2: Plan the Route Around the Minimum Bend Radius

This is the step that most often goes wrong with a smooth bore tube. The minimum bend radius grows quickly with diameter:

  • 60 mm at 5/32", 130 mm at 1/4", 160 mm at 5/16", 220 mm at 3/8"

  • 270 mm at 1/2", 400 mm at 5/8", 500 mm at 3/4"

  • 600 mm at 1", 800 mm at 1-1/4", 900 mm at 1-1/2" and 1200 mm at 2"

Measure the radius at the centreline of the tube, not at the inside edge. Keep a short straight section next to each end connection instead of bending right at the fitting. Where the layout cannot provide these radii, do not force the tube; a convoluted PTFE hose such as our JCC-10000 series is the better choice for tight turns.

Step 3: Cut and Prepare the Ends

  • Cut the tube square with a sharp cutter so the fitting seals evenly around the whole circumference.

  • Remove burrs and loose fragments from the bore, especially on high-purity and corrosive lines where particles must not enter the process.

  • Do not crush the end or leave it oval; an out-of-round end is a common source of weeps on compression or barb fittings.

Step 4: Make the End Connections

  • Use fittings that match the actual outer diameter in the table, for example 8.8 mm OD on the 1/4" tube and 15.7 mm OD on the 1/2" tube.

  • Push the tube fully into or onto the fitting and tighten evenly. Do not overtighten; PTFE can cold-flow under excessive clamp or nut load.

  • Hold the tube so it does not rotate as the fitting is tightened. Twisting a smooth bore tube about its axis is unnecessary stress and can loosen the opposite end.

Step 5: Support the Run

  • Support long horizontal runs at regular intervals so the tube does not sag into a tighter bend than the table allows, or rest on sharp edges and hot surfaces.

  • At each end, the support should leave the short straight section free, so the fitting is not loaded sideways.

  • Allow for thermal expansion and contraction between -70°C and +260°C. A tightly clamped long run with no movement will load the fittings when the temperature changes.

Step 6: Flush, Pressurise and Record

  1. Flush the line before commissioning; the non-stick bore makes this quick, but do it thoroughly when the previous medium is incompatible with the next one.

  2. Pressurise gradually and stay below the catalog working pressure for the size.

  3. Check every connection and every bend for leaks, flattening or kinks.

  4. Record the size, length and installation date so the line can be included in later inspections.

Common Routing Mistakes

Mistake

Likely result

Correction

Bend tighter than the catalog radius

Kink, flow restriction, early crack

Re-route, add length, or change to a convoluted hose

Bending directly at the fitting

Stress concentration and leaks

Leave a straight section at each end

No support on a long horizontal run

Sag, accidental tight bend

Add supports at regular intervals

Using burst pressure as the design limit

Overloaded tube

Size by working pressure

Overtightening the fitting

Distorted tube end, weep

Match the OD and tighten only as required

Order the JCC-00000-PTFE Tube

The catalog states that the tube can be customized according to parameters. Send us the medium and concentration, working and maximum temperature, working pressure, size (or custom dimensions), length and quantity, and JINGCHENG will confirm the right smooth bore PTFE tube and supply cut lengths or assemblies made to your parameters.

Previous: 
Next: 

Product Category

If you have any questions, please contact us via email or telephone and we will get back to you as soon as possible.

Contact Us

粤ICP备2023036405号-1

Copyright© 2023 JINCHEN ELECTRIC TRACING CO., LTD. All Rights Reserved.   Sitemap.   Support by Leadong