| Availability: | |
|---|---|
| Quantity: | |
Soren20061116
JINGCHENG
3917290000 3904610000 3917390000
JINGCHENG Crack Sealing Machine Hose is an electrically heated hose for road maintenance and crack sealing equipment, heat resistant up to 230°C and built with a unique inner tube reinforcement technology that secures its service life. This page breaks hose cost per season into six drivers — service life, energy and heat-up, sealant waste, sizing, downtime and operating practice — and links each one to the catalog facts that influence it.
For a road maintenance contractor, the heated hose on a crack sealing machine is a small part of the machine's value but a large part of its uptime. When a hose fails during the season, the cost is rarely the hose alone: the crew stands idle, sealant in the kettle may have to be held at temperature or wasted, a replacement must be sourced quickly, and the work window — often limited by weather and traffic control — is lost. Total cost of ownership therefore depends on how long the hose lasts, how reliably it heats, and how easy it is to specify and replace correctly. This guide sets out those cost drivers and the catalog facts that influence each of them.
JINGCHENG's crack sealing machine hose is an electrically heated hose for all types of road maintenance equipment and crack sealing equipment. It is heat resistant up to 230°C (higher on request) and is built with JINGCHENG's unique inner tube reinforcement technology, which secures the service life of the hose. Uniformly braided heating elements minimize the inner-wall temperature difference, and high-efficiency insulation is chosen with the hose surface temperature in mind.
Service life is the largest single factor in hose cost per working day. On a crack sealer the hose is heated daily, dragged along the pavement, flexed at the wand and coiled back on the machine. The reinforced inner tube is the feature the catalog singles out for this product; it is there to hold up to that daily cycle. Handling matters just as much: a hose that is never twisted sideways and never coiled tighter than its bend radius will simply last longer than one that is.
A hose that loses heat through its jacket uses more power and takes longer to bring sealant to working temperature at the start of each day. High-efficiency insulation keeps heat in the line, and the uniformly braided heating layer heats the bore evenly, so the controller does not have to overdrive one section to keep another warm. Choosing a rated power (110, 150, 170 or 200 W/m, or other) that matches the sealant and ambient conditions avoids both slow heat-up and unnecessary consumption.
Hot spots can overheat sealant, while cold sections let it thicken and restrict flow at the wand. Either way, material is wasted and the crack may need to be resealed. Even heating along the full length keeps the material at its intended application temperature from kettle to wand.
An undersized hose restricts output; an oversized one is heavier to handle and needs a wider coil on the machine. The catalog lists four sizes:
1/2" — 15.9 mm OD, 118 bar (1704 psi) working, 470 bar burst, 150 mm minimum bend radius.
5/8" — 19 mm OD, 88 bar (1269 psi) working, 350 bar burst, 180 mm bend radius.
3/4" — 22.6 mm OD, 85 bar (1234 psi) working, 340 bar burst, 260 mm bend radius.
1" — 29.5 mm OD, 75 bar (1088 psi) working, 300 bar burst, 300 mm bend radius.
Inner Diameter (inch) | Outer Diameter (mm ±0.2) | Working Pressure (bar) | Working Pressure (psi) | Burst Pressure (bar) | Burst Pressure (psi) | Min. Bend Radius (mm) |
|---|---|---|---|---|---|---|
1/2" | 15.9 | 118 | 1704 | 470 | 6815 | 150 |
5/8" | 19 | 88 | 1269 | 350 | 5075 | 180 |
3/4" | 22.6 | 85 | 1234 | 340 | 4930 | 260 |
1" | 29.5 | 75 | 1088 | 300 | 4350 | 300 |
Data source: JINGCHENG 2025 Electrically Heated Hose Catalog. Heat resistance up to 230°C; higher temperature on request. Confirm the rating at your operating temperature with our engineers when ordering.
The bend radius column is directly tied to cost: a hose rack, reel or hook that forces the hose tighter than its radius shortens service life on every run.
Because every JINGCHENG heated hose is built to order, the fastest replacement is one whose specification is already on file. Keep a record of each machine's hose: bore, length (3 m, 4.5 m, 5 m, 6 m, 10 m or other), supply voltage (380 Vac, 220 Vac, 110 Vac, 12 Vdc or other), sensor type (Type J or Type K thermocouple, Ni120, PT100 or PT1000), rated power, thread standard at each end (US, British or metric) and the pin layout at the controller end and the wand end. A model code such as JCH-200-16-B-3X220-P2-8 — working temperature, bore, inner-tube type, supply, sensor and working pressure — captures the core data in one line. With that record, a replacement or a spare can be ordered before the season starts rather than in the middle of it.
The catalog handling rules are simple, and each one protects the investment:
Do not twist the hose sideways during installation or use; lateral twisting can cause leakage, flow loss, hose damage or fire.
Avoid sharp bends, especially next to the fittings at the kettle end and the wand end.
Wire the hose according to its technical data and the pin table supplied with it.
Let authorized, trained and preferably dedicated operators handle the hose; unauthorized modification or adjustment voids the warranty.
Operate within the catalog conditions: ambient -40°C to +55°C and relative humidity not above 85%.
Size each hose from the four-row chart for the sealant output and the machine's coil geometry.
Match rated power and sensor type to the machine's controller.
Keep a specification record for every machine and consider a spare hose for peak season.
Train crews on twist-free handling and bend-radius limits.
Contact JINGCHENG engineers when a situation arises that the instructions do not cover.
Send the machine type, sealant and application temperature, required bore and length, supply voltage, sensor type and the thread standard at each end. JINGCHENG engineers will confirm a matching crack sealing machine hose specification and quotation; every hose is checked for defects before packing and shipment.
