Home » Products » PTFE Hose » Inner Spiral Convoluted PTFE Hose Size and Bend Radius Guide for Tight-Space Chemical Lines

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Inner Spiral Convoluted PTFE Hose Size and Bend Radius Guide for Tight-Space Chemical Lines

JINGCHENG Inner Spiral Convoluted PTFE Hose (series JCC-10000-PTFE) has corrugated inner and outer walls for extremely strong bending performance from -70°C to +260°C and is used in the pharmaceutical, food and chemical industries. This size and bend-radius guide shows how to read the ten catalog sizes from 1/4" (6.5 mm ID) to 2" (50 mm ID), with minimum bend radii from 20 mm to 125 mm and working pressures from 0.4 MPa down to 0.2 MPa, when the route is tight.
Availability:
Quantity:
  • Soren20061120

  • JINGCHENG

  • 3917290000 3904610000 3917390000

Inner Spiral Convoluted PTFE Hose Size and Bend Radius Guide for Tight-Space Chemical Lines

JINGCHENG Inner Spiral Convoluted PTFE Hose (series JCC-10000-PTFE) has corrugated inner and outer walls for extremely strong bending performance from -70°C to +260°C and is used in the pharmaceutical, food and chemical industries. This size and bend-radius guide shows how to read the ten catalog rows of the JCC-10000-PTFE hose — inner diameter, outer diameter, minimum bend radius from 20 mm to 125 mm and working pressure from 0.4 MPa to 0.2 MPa — when the route is tight.

How to Read the Size and Bend-Radius Table

The reason to choose an inner spiral convoluted PTFE hose is almost always the route: the line has to turn tightly, connect to a pump or a moving unit, or fit inside a compact skid. The catalog table then has to answer two questions at once — which inner diameter gives the flow you need, and whether that size can actually make the turns in the space you have. This page is a size and bend-radius guide for the JINGCHENG JCC-10000-PTFE hose, using the figures in the PTFE Hose Catalog.

According to the catalog, this hose has inner and outer walls that are both corrugated, giving it extremely strong bending performance. The temperature range is -70°C to +260°C, and it is listed as suitable for the pharmaceutical industry, food industry and chemical industry. Ten standard sizes run from 1/4" (6.5 mm ID) to 2" (50 mm ID), with ID and OD tolerance of ±0.3 mm. All specifications can be customized according to customer parameters.

Part No.

Nominal Size

Inner Diameter (mm ±0.3)

Outer Diameter (mm ±0.3)

Working Pressure (psi)

Working Pressure (MPa)

Burst Pressure (psi)

Burst Pressure (MPa)

Min. Bend Radius (inch)

Min. Bend Radius (mm)

JCC-10004-PTFE

1/4"

6.5

10.6

60

0.4

210

1.4

0.79

20

JCC-10008-PTFE

5/16"

8

12.3

60

0.4

210

1.4

0.87

22

JCC-10010-PTFE

3/8"

10

15

60

0.4

210

1.4

1.02

26

JCC-10013-PTFE

1/2"

13

17.9

60

0.4

210

1.4

1.02

26

JCC-10016-PTFE

5/8"

16

21.9

45

0.3

180

1.2

1.26

32

JCC-10019-PTFE

3/4"

19

26.4

45

0.3

180

1.2

2.17

55

JCC-10025-PTFE

1"

25

35

45

0.3

150

1

3.15

80

JCC-10032-PTFE

1-1/4"

32

39

38

0.3

135

0.9

3.94

100

JCC-10038-PTFE

1-1/2"

38

45

38

0.3

135

0.9

3.94

100

JCC-10050-PTFE

2"

50

59.5

30

0.2

120

0.8

4.92

125

Data source: JINGCHENG PTFE Hose Catalog (JCC-10000-PTFE Series). Operating temperature range: -70°C to +260°C. All specifications can be customized according to customer parameters.

Start With Inner Diameter and Flow

Nominal sizes step from 1/4" through 5/16", 3/8", 1/2", 5/8", 3/4", 1", 1-1/4", 1-1/2" and 2". The catalog inner diameters are 6.5, 8, 10, 13, 16, 19, 25, 32, 38 and 50 mm. Choose the ID from the required flow first, then check that the rest of the row still fits the layout. A size that looks right on flow can still fail the route if its bend radius or outer diameter is larger than the space around the turn.

Then Check the Minimum Bend Radius

This is where the convoluted hose earns its place. Minimum bend radii in the catalog are:

  • 20 mm at 1/4", 22 mm at 5/16", 26 mm at 3/8" and at 1/2"

  • 32 mm at 5/8", 55 mm at 3/4", 80 mm at 1"

  • 100 mm at 1-1/4" and at 1-1/2", 125 mm at 2"

Measure the radius at the centreline of the hose. Even though these values are small, they are still limits: do not crush the convolutions to gain a tighter turn. Leave a short straight section at each end fitting rather than starting the bend at the connection.

For a sense of scale, a 1/2" JCC-10000 hose may be bent to 26 mm, which is tight enough for most pump and valve connections on a compact skid. The same nominal 1/2" in our smooth bore JCC-00000 tube requires 270 mm. That difference is why this hose is chosen for tight-space chemical, food and pharmaceutical lines. If a single turn in the layout is tighter than the table value for the ID you need, either add length and open the turn, or discuss a custom construction — do not force the hose.

Allow for Outer Diameter at Clamps and Pass-Throughs

The corrugation adds height, so the outer diameter is larger than a smooth tube of the same ID. Catalog ODs are 10.6, 12.3, 15, 17.9, 21.9, 26.4, 35, 39, 45 and 59.5 mm. Check these values when you select clamps, sleeves, panels and wall pass-throughs. A clamp sized only on the inner diameter will be too small.

Keep the Pressure Inside the Row You Have Chosen

The same convolutions that give flexibility also limit pressure. Working pressure is:

  • 0.4 MPa (60 psi) from 1/4" to 1/2"

  • 0.3 MPa (45 psi) from 5/8" to 1", and 0.3 MPa (38 psi) at 1-1/4" and 1-1/2"

  • 0.2 MPa (30 psi) at 2"

Burst pressure ranges from 1.4 MPa down to 0.8 MPa and is a safety margin only. If the line needs both tight bends and a higher working pressure, look at a braided convoluted version such as our JCC-11100 series rather than overloading this unbraided hose.

A Practical Way to Lock the Size

  1. Choose the inner diameter from flow.

  2. Check that every planned turn is no tighter than the minimum bend radius for that row.

  3. Check that clamps and openings accept the outer diameter.

  4. Confirm that the highest system pressure stays below the working pressure for that size.

  5. If any one of those four checks fails, move one size up or down, add length, or ask us about a custom size. The catalog states that the hose can be customized according to parameters.

Routing Notes That Protect the Chosen Radius

  • Do not twist the hose about its axis when tightening connections; twisting is not a substitute for a larger radius.

  • Support long horizontal runs so the hose does not sag into a tighter curve than the table allows.

  • Flush the ridged bore thoroughly between products, especially on food and pharmaceutical lines.

What to Send for a Quotation

Send the medium, temperature (within -70°C to +260°C), working pressure, the ID you prefer, the tightest bend in the route, the length and the end-connection details. JINGCHENG will confirm whether the JCC-10000-PTFE size in the table meets the route and the pressure, or will propose a custom size or a different construction.

Previous: 
Next: 

Product Category

If you have any questions, please contact us via email or telephone and we will get back to you as soon as possible.

Contact Us

粤ICP备2023036405号-1

Copyright© 2023 JINCHEN ELECTRIC TRACING CO., LTD. All Rights Reserved.   Sitemap.   Support by Leadong